Tuesday, May 17, 2011

Build a Wi-Fi antenna using household materials

 

Who'd have thought that a toilet-brush holder, of all things, would turn out to be an excellent Wi-Fi antenna? The lesson is that you can achieve great results for little expense - and half an hour's work.The range of a WiFi router can be considerably extended simply by connecting a directional antenna. Standard omni-directional stub antennas are at the lower end of the performance scale, and they quickly come up against their limits when you need to give your own home better coverage, provide your neighbour with DSL, or pick up as many radio networks as possible while war driving.If the access point is three rooms further on, or even in the house on the other side of the road, you need a directional antenna. If you have to make a connection to your nearest DSL-equipped acquaintance at the other end of the village street, or to bridge even longer radio links to reach the free radio[1] node in the next block but one, you may even require two directional antennas.

Neighbourhood WiFi routers with omni-directional aerials are in any case the worst sources of interference in a city. A single block of flats can easily contain over ten wireless networks, all chattering away simultaneously. Mutual interference is inevitable, with the result that range and connection stability are drastically reduced.Replacing just one of two antennas at the base station can be a way of improving WiFi coverage, for example, down to the bottom of the garden. The near zone is served by the remaining stub. All current WiFi modules automatically use the most suitable antenna for each client, a process called antenna diversity. Even with models having only one external antenna, it's worth having a look inside the casing. Usually, a tiny socket for the second antenna is fitted on the WiFi module. Depending on the manufacturer, this type of plug is called U.FL or Ipex. The connection can easily be led out through a ventilation slot with a short adaptor cable ("pigtail"). On some WiFi notebook cards and USB sticks, there is also an antenna plug, and a look at the data sheet will tell you its type – normally SMA or RPSMA.

The simply made tin-can antenna, with the dimensions given here, is suitable for base stations and for clients who transmit on 2.4 GHz in accordance with the IEEE 802.11b and 802.11g standards. 802.11a uses the 5-GHz band, requiring different antenna dimensions. The necessary background for a recalculation is given in an article on building tin-can radio antenna (Building a Wi-Fi Antenna Out of a Tin Can) [2]

Very recent base stations that comply with the draft standard 802.11n also use the 2.4 GHz band. But they automatically use a number of methods to combine their antennas for optimal range and speed. However, this only works if the antennas have the characteristics expected by the WiFi chipset.

 

http://www.h-online.com/features/Build-a-Wi-Fi-radio-relay-using-household-materials-747382.html?view=print

Hex Beam antenna

 

I am currently looking at building a Hexx wire beam antenna. Due to space restrictions and various things w.r.t antennas in New Zealand I do think that this antenna can work for me.
I had a browse around and found a couple of websites referring to hexx beams and how to make it.It seems fairly easy and with a 5 band version all on one feed line it is well worth investigating.
Here is a picture of a typical Hexx beam:


So, how should I start,I managed to get a aluminium base plate at a scrap metal shop for a good price, Picked up some old PVC 20mm tube in 2 m lenghts and have wire I collected over the years.I made the PVC into 2m lengths to accommodate a 3 band antenna which will host 10m / 12m / 15m (28mhz / 24mhz / 21mhz).Now I made the aluminium base plate into a HEXX shape. With my thinking cap on I managed to make a Hexx shape. What a story if you do not have a compass.

The Wire needs to be added and this is what it should look like from above once completed.

 

I will post pictures as I progress so be sure to check back to follow my progress.

http://zs6lw.blogspot.com/2009/11/hexx-beam-antenna.html

MOSFET-BASED PREAMPLIFIER FOR FM RADIO Project

 

FM transmissions can be received within a range of 40 km. If you are in fringe areas, you may get a very weak signal. FM DXing refers to hearing distant stations (1500 km or more) on the FM band (88-108 MHz). The term ‘DX’ is borrowed from amateur radio operators. It means ‘distance unknown’; ‘D’ stands for ‘distance’ and ‘X’ stands for ‘unknown.’ For an FM receiver lacking gain, or having a poor signal-to-noise ratio, using an external preamplifier improves the signal level.

The dual-gate MOSFET preamplifier circuit shown in Fig. 1 gives an excellent gain of about 18 dB. It costs less and is simple to design. Field-effect transistors (FETs) are superior to bipolar transistors in many applications as these have a much higher gain—approaching that of a vacuum tube. These are classified into junction FETs and MOSFETs. On comparing the FETs with a vacuum tube, the gate implies the grid, the source implies the cathode, and the drain implies the plate.In a transistor, the base implies the grid, the emitter implies the source, and the collector implies the drain. In dual-gate FETs, gate 1 is the signal gate and gate 2 is the control gate. The gates are effectively in series, making it easy to control the dynamic range of the device by varying the bias on gate 2. The MOSFET is more flexible because it can be controlled by a positive or negative voltage at gate 2. The resistance between the gate and rest of the device is extremely high because these are separated by a thin dielectric layer. Thus the MOSFET has an extremely high input impedance. Dual-gate MOSFETs (DG MOSFETs) are very popular among radio amateurs. These are being used in IF amplifiers, mixers, and preamplifiers in HF-VHF transceivers.

The isolation between the gates (G1 and G2) is relatively high in mixer applications. This reduces oscillator pulling and radiation. The oscillator pulling is troublesome particularly in shortwave communications. It is a characteristic in many unsophisticated frequency-changer stages, where the incoming signal, if large, pulls the oscillator frequency slightly off the frequency set by the tuning knob and towards a frequency favourable to the (large) incoming signal. A DG MOSFET can also be used for automatic gain control in RF amplifiers. DG MOSFET BF966S is an n-channel depletion-type MOSFET that is used for general-purpose FM and VHF applications.


In this configuration, it is used for FM radio band. The quadratic input characteristic of the FET input stage gives better results than the exponential characteristic of a bipolar transistor. Gate 1 is meant for input and gate 2 is for gain control. The input from the antenna is fed to gate G1 via C1 and L1. Trimmer VC1 is used to tune and select the input frequencies. Capacitor C4 (100 kpF) at the gain control electrode (gate 2) decouples any variation in G2 voltage at radio frequencies to maintain constant gain. Set preset VR (47k) to adjust the gain or connect a fixed resistor for fixed gain. The output of the circuit is obtained via capacitor C5 and fed to the FM receiver amplifier.

For indoor use, connect a ¼- wavelength whip antenna, ½-wavelength 1.5m wire antenna, or any other indoor antenna set-up with this circuit. You may use a 9V battery without the transformer and diode 1N4007, or any 6V-12V power supply to power the circuit (refer Fig. 1). The RF output can be taken directly through capacitor C5. For an improved input and output impedance, change C1 from 1 kpF to 22 pF and C5 from 1 kpF to 100 kpF. For outdoor use at top mast, like a TV booster, connect the C5 output to the power supply unit (PSU) line. Use RG58U/ RG11 or RG174 cable for feeding the power supply to the receiver amplifier. The PSU for the circuit is the same as that of a TV booster. For TV boosters, two types of mountings are employed: The fixed tuned booster is mounted on the mast of the antenna. The tunable booster consisting of the PSU is placed near the TV set for gain control of various TV channels. (For details, refer ‘High-Gain 4-Stage TV Booster’ on page 72 of Electronics Projects Vol. 8.) Mount the DG MOSFET BF966S at the solder side of the PCB to keep parasitic capacitance as small as possible. Use an epoxy PCB. After soldering, clean the PCB with isopropyl alcohol. Use a suitable


enclosure for the circuit. All component leads must be small. Avoid shambled wiring to prevent poor gain or self oscillations. Connecting a single-element cubical quad antenna to the circuit results in ‘Open Sesam’ for DXing.You can use a folded dipole or any other antenna. However, an excellent performance is obtained with a cubical quad antenna (refer Fig. 2) and Sangean ATS- 803 world-band receiver. In an amplifier, FET is immune to strong signal overloading. It produces less cross-modulation than a conventional transistor having negative temperature coefficient, doesn’t succumb to thermal runaway at high frequencies, and decreases noise. In VHF and UHF, the MOSFET produces less noise and is comparable with JFETs. DG FETs reduce the feedback capacitance as well as the noise power coupled to the gate from the channel, giving stable unneutralised power gain for wide-band applications. This circuit can be used for other frequency bands by changing the inputand the output LC networks. The table here gives details of the network components for DXing of stations at various frequency bands.